wiki:v2:mounting_pixy_with_lego
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
wiki:v2:mounting_pixy_with_lego [2019/01/26 01:29] pixycam |
wiki:v2:mounting_pixy_with_lego [2019/01/30 20:27] (current) pixycam |
||
|---|---|---|---|
| Line 28: | Line 28: | ||
| Weird. But it's **important** for this first step: | Weird. But it's **important** for this first step: | ||
| - | 1. Using two of the **long fasteners**, attach the **2-threaded brackets** to the LEGO brick so that **the long legs are pointing out, and the short legs are touching the brick.**\\ | + | 1. Using two of the **long fasteners**, attach the **2-threaded brackets** to the LEGO brick so that **the long legs are pointing out, and the short legs are touching the brick.** If you attach the other way around Pixy2 won't fit!\\ |
| - | {{wiki:img:bddc68458f9ddc89bdc8199f932433f6c52b683a.jpg?400}} | + | {{wiki:v1:img_5326_result.jpg?400}}\\ |
| + | {{wiki:v1:img_5327_result.jpg?400}} | ||
| + | \\ | ||
| \\ | \\ | ||
| 2. Using two of the **short fasteners**, attach two **1-threaded brackets** to your Pixy2 as shown in the picture below.\\ | 2. Using two of the **short fasteners**, attach two **1-threaded brackets** to your Pixy2 as shown in the picture below.\\ | ||
| Line 35: | Line 37: | ||
| {{wiki:v2:img_5173_result.jpg?400}} | {{wiki:v2:img_5173_result.jpg?400}} | ||
| \\ | \\ | ||
| + | \\ | ||
| 3. Take two **nylon bushings** and press them into the non-threaded holes in these brackets.\\ | 3. Take two **nylon bushings** and press them into the non-threaded holes in these brackets.\\ | ||
| {{wiki:v2:img_5161_result.jpg?400}} | {{wiki:v2:img_5161_result.jpg?400}} | ||
| \\ | \\ | ||
| - | + | \\ | |
| 4. Slide the Pixy2 into the brick assembly. It should fit nice and snug! Use two of the **medium fasteners**, and insert them from the inside as shown in the picture.\\ | 4. Slide the Pixy2 into the brick assembly. It should fit nice and snug! Use two of the **medium fasteners**, and insert them from the inside as shown in the picture.\\ | ||
| - | {{wiki:img:9f58a7327757cbb7950b00c046594788b98e3104.jpg?400}} | + | {{wiki:v1:img_5332_result.jpg?400}} |
| + | \\ | ||
| \\ | \\ | ||
| - | |||
| - | |||
| The fasteners form an axle that you can use to tilt Pixy2 up and down. Inserting the screws from the inside allows you to tighten them down, so Pixy2 holds the desired tilt angle.\\ | The fasteners form an axle that you can use to tilt Pixy2 up and down. Inserting the screws from the inside allows you to tighten them down, so Pixy2 holds the desired tilt angle.\\ | ||
| - | {{wiki:img:4ef644598e54018a30718786b257b64ee3932b80.jpg?400}} | + | {{wiki:v1:img_5335_result.jpg?400}} |
wiki/v2/mounting_pixy_with_lego.1548466198.txt.gz · Last modified: 2019/01/26 01:29 by pixycam
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
