wiki:v2:hooking_up_pixy_to_a_raspberry_pi
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
wiki:v2:hooking_up_pixy_to_a_raspberry_pi [2018/06/29 03:09] pixycam |
wiki:v2:hooking_up_pixy_to_a_raspberry_pi [2018/06/29 23:54] pixycam |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| ====== Hooking up Pixy2 to a Raspberry Pi ====== | ====== Hooking up Pixy2 to a Raspberry Pi ====== | ||
| - | ====== 1. Introduction ====== | + | Hooking up Pixy2 to your Raspberry Pi entails building the libpixyusb2 library, so your Pixy2 can talk over USB to your Raspberry Pi. |
| - | + | ||
| - | The following procedure outlines the steps required to build the 'get blocks' example on a Raspberry Pi using the Raspberrian distribution. The 'get blocks' example is a simple program that demonstrates how to read blocks and send commands to the Pixy2 over USB like PixyMon. | + | |
| - | + | ||
| - | You will need: | + | |
| - | + | ||
| - | * SD Card withinstalled | + | |
| - | * USB Hub with at least three ports | + | |
| - | * Pixy2 updated to latest firmware | + | |
| - | + | ||
| - | NOOBS is available from the Raspberry Pi website here: http://www.raspberrypi.org/downloads/ | + | |
| - | + | ||
| - | + | ||
| - | ====== 2. Procedure ====== | + | |
| - | + | ||
| - | + | ||
| - | ===== 2.1. Raspberry Pi Hardware Setup ===== | + | |
| - | + | ||
| - | + | ||
| - | ==== 2.1.1. Connect your Raspberry Pi to the Internet ==== | + | |
| - | + | ||
| - | Using an Ethernet cable, connect the Raspberry Pi to an internet source as shown below. | + | |
| - | + | ||
| - | {{wiki:img:c915bad8138d82804e0f7f1360e4bbb54877be2f.jpg?400}} | + | |
| - | + | ||
| - | + | ||
| - | ==== 2.1.2. Connect your Raspberry Pi to a video display ==== | + | |
| - | + | ||
| - | Using an HDMI cable, connect the Raspberry Pi to a video display as shown below. | + | |
| - | + | ||
| - | {{wiki:img:f3e7d4db3cdd88a0b0271ecee6465a8c3ec70a31.jpg?400}} | + | |
| - | + | ||
| - | + | ||
| - | ==== 2.1.3. Connect Keyboard, Mouse, and Pixy2 to USB hub ==== | + | |
| - | + | ||
| - | The Raspberry Pi only has two USB ports, so a hub is needed to connect Pixy2, a keyboard, and mouse simultaneously. Using the hub, connect your keyboard, mouse, and Pixy2 to the Raspberry Pi. | + | |
| - | + | ||
| - | {{wiki:img:0ba4d834c473bc80612ef7d56b16f651885e1359.jpg?400}} | + | |
| - | + | ||
| - | {{wiki:img:0f3cc1187a5d1786ac8475c3593760ca12faf4f4.jpg?400}} | + | |
| - | + | ||
| - | + | ||
| - | ==== 2.1.4. Insert NOOBS SD Card ==== | + | |
| - | + | ||
| - | {{wiki:img:fb504ec6eb8315298494cb0af421c2f1a7b0cd1b.jpg?400}} | + | |
| - | + | ||
| - | + | ||
| - | ==== 2.1.5. Connect power to Raspberry Pi ==== | + | |
| - | + | ||
| - | + | ||
| - | ===== 2.2. Raspberry Pi Software Setup ===== | + | |
| - | + | ||
| - | + | ||
| - | ==== 2.2.1. Install Raspberrian ==== | + | |
| - | + | ||
| - | On first boot, NOOBS will display a list of install options for the Raspberry Pi. Select Raspberrian and click the install button. | + | |
| - | + | ||
| - | {{wiki:img:3813c1ec648f985df1feb6dc07532fc5396cd02d.jpg?400}} | + | |
| - | + | ||
| - | Click the 'Yes' button to confirm installing. | + | |
| - | + | ||
| - | {{wiki:img:c2c578b0804acf6d6de033b52a674c81f463ebd1.jpg?400}} | + | |
| - | + | ||
| - | The installer will begin installing Raspberry Pi system files. This will take some time. | + | |
| - | + | ||
| - | {{wiki:img:ce2a12811782166aab553eeb45c023b5278056b6.jpg?400}} | + | |
| - | + | ||
| - | When the installer is finished, click the 'OK' button to restart. | + | |
| - | + | ||
| - | {{wiki:img:60475cf88d2bc03143339e1526fe3f4671bb9511.jpg?400}} | + | |
| - | + | ||
| - | When the Raspberry Pi boots, the configuration menu will be displayed. Select the 'Enable Boot to Desktop/Scratch...' option. | + | |
| - | + | ||
| - | {{wiki:img:dc100ed14d7353cd103fbee235d9459b39f847f6.jpg?400}} | + | |
| - | + | ||
| - | Select 'Desktop log in as user pi at the graphical desktop' and select 'OK'. | + | |
| - | + | ||
| - | {{wiki:img:03b03c074fa339660ba61dce1662da34476ae320.jpg?400}} | + | |
| - | + | ||
| - | Select 'Finish' to exit the configuration menu. | + | |
| - | + | ||
| - | {{wiki:img:796d1759f69b82f172558c9c1b92238d9a8e412c.jpg?400}} | + | |
| - | + | ||
| - | Select 'Okay' to reboot. | + | |
| - | + | ||
| - | {{wiki:img:7fc275462ba3c4b1b4e9ee2a5b2a5a0c29c605ff.jpg?400}} | + | |
| - | + | ||
| - | + | ||
| - | ===== 2.3. Software Dependency Installation ===== | + | |
| - | + | ||
| - | From the Raspberry Pi desktop, start the LXTerminal application. | + | |
| - | + | ||
| - | {{wiki:img:d8ffb7ac38d09d2f5f35ab1bb3d57dd582f0b736.jpg?400}} | + | |
| - | + | ||
| - | + | ||
| - | ==== 2.3.1. Install libusb ==== | + | |
| - | + | ||
| - | In the terminal window type: | + | |
| - | + | ||
| - | ''%%sudo apt-get install libusb-1.0-0.dev%%'' | + | |
| - | + | ||
| - | + | ||
| - | ===== 2.4. Install Pixy2 Source Code ===== | + | |
| - | + | ||
| - | In the terminal window type: | + | |
| - | + | ||
| - | ''%%git clone https://github.com/charmedlabs/pixy2.git%%'' | + | |
| - | + | ||
| - | + | ||
| - | ===== 2.5 Build and install libpixyusb2 ===== | + | |
| - | + | ||
| - | + | ||
| - | ==== 2.5.1. Build the library ==== | + | |
| - | + | ||
| - | In the terminal window type: | + | |
| - | + | ||
| - | ''%%cd pixy2/scripts%%''\\ | + | |
| - | ''%%./build_libpixyusb2.sh%%'' | + | |
| - | + | ||
| - | + | ||
| - | + | ||
| - | ===== 2.6. Running the 'get_blocks' example ===== | + | |
| - | + | ||
| - | + | ||
| - | ==== 2.6.1. Build the example ==== | + | |
| - | + | ||
| - | In the terminal window type: | + | |
| - | + | ||
| - | ''%%./build_get_blocks_cpp_demo.sh%%'' | + | |
| - | + | ||
| - | + | ||
| - | ==== 2.6.2. Run the example ==== | + | |
| - | + | ||
| - | In the terminal window type: | + | |
| - | + | ||
| - | ''%%cd ../build/hello_pixy%%''\\ | + | |
| - | ''%%sudo ./hello_pixy%%'' | + | |
| - | + | ||
| - | The output should look like something below: | + | |
| - | + | ||
| - | ''%%Hello Pixy:%%''\\ | + | |
| - | ''%% Example Version: 0.3%%''\\ | + | |
| - | ''%% Pixy Firmware Version: 1.0.2%%''\\ | + | |
| - | ''%%Detecting blocks...%%''\\ | + | |
| - | ''%%[sig: 1 w: 11 h: 17 x:149 y: 46]%%''\\ | + | |
| - | ''%%[sig: 1 w: 9 h: 21 x:148 y: 46]%%''\\ | + | |
| - | ''%%[sig: 1 w: 14 h: 21 x:151 y: 45]%%''\\ | + | |
| - | ''%%[sig: 1 w: 10 h: 19 x:149 y: 47]%%''\\ | + | |
| - | ''%%[sig: 1 w: 8 h: 16 x:148 y: 49]%%''\\ | + | |
| - | ''%%[sig: 1 w: 9 h: 19 x:148 y: 45]%%''\\ | + | |
| - | ''%%[sig: 1 w: 12 h: 6 x:150 y: 54]%%''\\ | + | |
| - | ''%%[sig: 1 w: 15 h: 18 x:151 y: 46]%%''\\ | + | |
| - | ''%%[sig: 1 w: 11 h: 5 x:149 y: 54]%%''\\ | + | |
| - | ''%%[sig: 1 w: 9 h: 7 x:148 y: 49]%%''\\ | + | |
| - | ''%%[sig: 1 w: 11 h: 5 x:149 y: 50]%%''\\ | + | |
| - | ''%%[sig: 1 w: 8 h: 6 x:148 y: 47]%%''\\ | + | |
| - | ''%%[sig: 1 w: 10 h: 7 x:149 y: 51]%%'' | + | |
| - | + | ||
| - | The example does the following | + | |
| - | + | ||
| - | - Connects to Pixy2 using USB | + | |
| - | - Displays firmware version installed on Pixy2 | + | |
| - | - Block information is displayed if color signatures have been set and if the signatures are currently being detected by Pixy2. | + | |
| - | + | ||
| - | + | ||
| + | {{page>wiki:v2:building_the_libpixyusb_example_on_linux&noheader&noindent}} | ||
wiki/v2/hooking_up_pixy_to_a_raspberry_pi.txt · Last modified: 2018/06/29 23:55 by pixycam
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
