wiki:v2:assembling_pantilt_mechanism
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Next revision Both sides next revision | ||
|
wiki:v2:assembling_pantilt_mechanism [2018/10/24 21:16] pixycam |
wiki:v2:assembling_pantilt_mechanism [2018/10/24 21:17] pixycam |
||
|---|---|---|---|
| Line 131: | Line 131: | ||
| 21 - Use a short 4-40 fastener to attach the fastener to Pixy as shown. | 21 - Use a short 4-40 fastener to attach the fastener to Pixy as shown. | ||
| - | |||
| {{wiki:v2:img_5209_result.jpg?640}} | {{wiki:v2:img_5209_result.jpg?640}} | ||
| 22 - Plug a USB cable into Pixy to let Pixy power-up and "zero" the servos. | 22 - Plug a USB cable into Pixy to let Pixy power-up and "zero" the servos. | ||
| - | |||
| {{wiki:v2:img_5212_result.jpg?640}} | {{wiki:v2:img_5212_result.jpg?640}} | ||
| 23 - Leave the USB cable plugged-in and attach the tilt servo horn to the tilt servo. The servo horn and Pixy should be close to upright as shown. | 23 - Leave the USB cable plugged-in and attach the tilt servo horn to the tilt servo. The servo horn and Pixy should be close to upright as shown. | ||
| - | |||
| {{wiki:v2:img_5213_result.jpg?640}} | {{wiki:v2:img_5213_result.jpg?640}} | ||
| 24 - Attach the base to the pan servo as shown. | 24 - Attach the base to the pan servo as shown. | ||
| - | |||
| {{wiki:v2:img_5216_result.jpg?640}} | {{wiki:v2:img_5216_result.jpg?640}} | ||
| 25 - Use the servo horn fasteners (found in the servo baggies) to attach the tilt and pan servo horns. | 25 - Use the servo horn fasteners (found in the servo baggies) to attach the tilt and pan servo horns. | ||
| - | |||
| {{wiki:v2:img_5218_result.jpg?640}} | {{wiki:v2:img_5218_result.jpg?640}} | ||
| {{wiki:v2:img_5222_result.jpg?640}} | {{wiki:v2:img_5222_result.jpg?640}} | ||
| Line 157: | Line 152: | ||
| 26 - The base plate has two hole patterns for attaching the standoffs: a rectangular hole pattern that we showed above and an Arduino hole pattern if you want to mount your Pixy pan-tilt on top of an Arduino. If you wish to mount your Pixy pan-tilt on top of an Arduino, see below. | 26 - The base plate has two hole patterns for attaching the standoffs: a rectangular hole pattern that we showed above and an Arduino hole pattern if you want to mount your Pixy pan-tilt on top of an Arduino. If you wish to mount your Pixy pan-tilt on top of an Arduino, see below. | ||
| - | |||
| {{wiki:v2:img_5228_result.jpg?640}} | {{wiki:v2:img_5228_result.jpg?640}} | ||
| {{wiki:v2:img_5230_result.jpg?640}} | {{wiki:v2:img_5230_result.jpg?640}} | ||
wiki/v2/assembling_pantilt_mechanism.txt ยท Last modified: 2019/02/13 21:10 by jfrench
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
