<< return to Pixycam.com

User Tools

Site Tools


wiki:v1:mounting_pixy

Mounting Pixy

Pixy was designed to befriend your robot or any other device you've dreamed up. So, with each Pixy we include brackets and fasteners to make mounting Pixy to your device fairly simple.

Here's what you'll need:

A small phillips screwdriver
43bf2c08420b60aee7e6c884858a9ab9fc270f98.jpg

Your Pixy
3040e853fc70322c8badb9e198cb95906fb4e596.jpg

The bag of fasteners that came with your Pixy
2094c133daa818e5185f6abd0d6903ba23f60d40.jpg

Before we continue, take all four right-angle brackets out of the little baggie and examine them. Notice that two of them have two threaded holes and two of them have one threaded hole. We'll call these two-threaded and one-threaded brackets, respectively. Go ahead and separate these two bracket types to make things easier.

Notice also that the baggie contains two different types of fasteners, three longer fasteners and five shorter fasteners. All of them are the same 4-40 thread.

Right-angle mount

The simplest way to mount Pixy is at a right angle, which is usually all that's required. Take two of the shorter 4-40 fasteners and two of the two-threaded brackets (or one-threaded brackets if you wish) and attach to Pixy as shown.

But first, a word about the two-threaded brackets. If you look really closely at one of these guys, you'll notice that one of its legs is ever-so-slightly longer than the other. Say what? It's true— I don't know why. But you can best see this by looking at the holes in the bracket. One of the holes in centered in its leg and the other hole is not centered, because its leg is slightly longer. Weird. Just make sure that when you use the two-threaded bracket you keep this in mind, otherwise your Pixy might look a little crooked after you finish mounting. Just a heads-up, to prevent some possible confusion.

Back mount

78bc17bb5d6d5087ab8439cbbe7c4f34b64998df.jpg

Front mount

f8dd28e35b5c1876ec61f9cc32bf95d4fec6ce9a.jpg

You can then mount Pixy by drilling some holes into your device and using the supplied 4-40 fasteners (long or short). Or you can use self-tapping fasteners (wood or sheet-metal fasteners) and the one-threaded brackets to attach Pixy to your device. Use the handy dandy drill template to make drilling the holes easier.

Tilt pivot mount

Sometimes you want to be able to adjust the tilt angle of your sensor so it's looking where you want it to look (down or up). You can do this with a motorized tilt, using a similar mechanism to the pan/tilt. Or you can use a fixed, but adjustable tilt pivot mount, which is what we'll describe now.

Start by attaching the one-threaded brackets to Pixy with the shorter 4-40 fasteners as shown in the picture.

89784cd4202000dc783fc2b87ed08da499a01e12.jpg

Then attach the two-threaded brackets with two more shorter 4-40 fasteners. Refer to the picture below.

3187893c90c8aeb5812797f9b8616b5c619df29d.jpg

You can then mount Pixy by drilling some holes into your device and using the long 4-40 fasteners. Or you can use self-tapping fasteners that will fit though the holes in the bracket. Use the handy dandy drill template to make drilling the holes easier.

Choose the tilt angle you like best and tighten the fasteners tight. Readjust by loosening/re-tightening.

929da9f3cbdb233e1cd5339f1141e3d938ab69e4.jpg
d88d0158e86d62a88df5f84b8bb024be002f26b1.jpg

wiki/v1/mounting_pixy.txt · Last modified: 2017/12/19 21:33 by jfrench